Technics SA-600 specifications

Category : Receiver

General

connectors

Technical data

amplifier

Tuner

special features

number of inputs: 6
- Phono: 2.5 mV, 47 k643961b8da111c0a15d770a1109a86d4
- Aux: 150 mV, 33 k643961b8da111c0a15d770a1109a86d4
- Playback Tape 1: 150 mV, 33 k643961b8da111c0a15d770a1109a86d4
- Playback Tape 2: 150 mV, 33 k643961b8da111c0a15d770a1109a86d4
- FM
- MW antenna
number of outputs: 2
- Rec Out Tape 1: 150 mV (RCA/ DIN)
- Rec Out Tape 2: 150 mV (RCA)
sockets 2 mesh (US standard) both for max. 150 Watt designed a switched, one unswitched
- These outlets are in Germany because of the VDE standard audit

continuous power output (20 - 20'000 Hz and total harmonic distortion of 0.04%)
- 8 643961b8da111c0a15d770a1109a86d4: 2x 70 W
- 4 643961b8da111c0a15d770a1109a86d4: 2x 80 W
dynamic performance (in the case of total harmonic distortion of 0.04%) approved
- 8 643961b8da111c0a15d770a1109a86d4s:
- 4 643961b8da111c0a15d770a1109a86d4:
total harmonic distortion: 0.04% in
power bandwidth:
- 4 643961b8da111c0a15d770a1109a86d4: 10 - 35,000 Hz (- 3 dB)
damping factor:
- 8 643961b8da111c0a15d770a1109a86d4: 50
- 4 643961b8da111c0a15d770a1109a86d4s: 25
frequency response:
- Phono (RIAA): 30 - 15,000 Hz (± 0.2 dB)
- AUX:
  - 10 - 40,000 Hz (- 1 dB)
  - 20 - 20,000 Hz (± 0.5 dB)
signal-to-noise ratio: 90 dB (Phono)
sound-control:
- Bass: 50 Hz, ± 10 dB
- treble: 10 kHz, ± 10 dB
Loudness: Yes
High Filter : Yes
Low Filter (Subsonic): Yes
Mute: no

receiving: FM/ MW
frequency:
- FM: 88 - 108 MHz
- MW: 530 - 1605 KHz
input sensitivity:
- FM: 0.9 µV (S/n 20 dB, 75-643961b8da111c0a15d770a1109a86d4)
- FM: 1,3 µV (S/R 30 dB, 75-643961b8da111c0a15d770a1109a86d4)
- FM: 1,9 µV (Usable)
- MW: 300 µV
frequency response:
- FM: 20 - 15,000 Hz (+ 1 dB, - 2 dB)
- FM: 20 - 14,000 Hz (±1.5 dB)
total harmonic distortion:
- Mono: 0,15%
- Stereo: 0.3% of
signal-to-noise ratio:
- Mono: 60 dB (75 dB, IHF)
- Stereo: 56 dB (70 dB, IHF)
channel separation:
- 1 kHz: 45 dB
- 10 kHz: 35 dB
selectivity: 70 dB
frequency selection: 1.2 dB
in addition to the wave selection: 70 dB
mirror frequency attenuation:
- FM: 70 dB (98 Mhz)
- MW: 45 dB
ZF-loss:
- FM: 90 dB
- MW: 40 dB
ON-suppression: 55 dB

sources and protection circuit display with LED
two-tone 2x 5 Element LED output power indicator
- on/ Off and factor selectable
High - and low-frequency Filter , or reverse the function for the gain (Boost)
gridded volume and tone controls
Separate Signal and tuning indicator
FM Muting
connection for two tape decks with the monitor function
wooden Cabinet
Pre-/power amplifier can be separated

The SA 600, it was only on the American market. However, the device can be switched from 110V to 220V or 240V. The scale lighting is provided by light bulbs with bayonet closure. The original bulbs were dipped in light blue lacquer. Colorless replacement bulbs are available here: BA9S, 6.3V 0.25A
The receiver fits optically perfectly to the tape machines of Technics (RS-1500US, RS-1506US and RS-1700), if they are equipped with the wooden side parts.