Camtech P101 specifications

Category : Power amplifiers

Brand : Camtech

General

Connections

Tech nical data

Special equipment

  • Manufacturer: Cambridge System Tech nologies (CST) - sold in Germany by Püllmanns under the brand Camtech (otherwise Audiolab )
  • Model: P101
  • Years of construction: From the beginning to the mid-90s
  • Manufactured in: England
  • Color: Black
  • Type: Stereo/Analog
  • Remote control: no
  • Power consumption: 20/480W (idle/full power)
  • Dimensions: 45/8/33 Width/height/depth (cm)
  • Weight: approx. 9 kg
  • < li>Factory price approx.: 2650 DM (according to STEREO 6/1991)
  • Number of inputs:
    • 1 x Stereo Input (700mV / 50kOhm ||400pF)
    • 1 x Stereo Load
  • Number of outputs:
    • 2 x Output left
    • 2 x Output right
  • 1 x Stereo Input (700mV/ 50kOhm ||400pF)
  • 1 x Stereo Load
  • 2 x Output left
  • 2 x Output right
  • Continuous power (with total harmonic distortion)
    • 8 ohm: > 100/120W (0.1%/1.0% THD+N)
    • 4 Ohm : >150W (1.0% THD+N)
  • Dynamic power
    • 4 ohm: > 250W
    • 2 Ohm : > 350W
  • Total harmonic distortion: max. 0.1%
  • Attenuation factor: 0.02 Ohm at 40Hz
  • Frequency response: 20Hz - 20,000Hz max +/- 0.3dB; 3Hz - 100,000Hz max. +/-3.0dB
  • Signal-to-noise ratio: > 115 dB
  • Stereo channel separation: >70dB
  • 8 Ohm s: > 100/120W (0.1%/1.0% THD+N)
  • 4 ohms: > 150W (1.0% THD+N)
  • 4 Ohm : > 250W
  • 2 Ohm : > 350W
  • Additional RCA RCA input with the designation LOAD in order to be able to adapt the input impedance to the preamplifier.
  • Bi-wiring speaker connector with the possibility of accommodating 4mm banana plugs (not CE variant).
  • Electronic protection circuit with low speaker impedance less than 2Ohm and short circuit.
  • Differential input stage with paired double JFETs 3SK389
  • Autozero offset compensation by integrator circuit
  • Transistor manufacturers dropped for driver and output stage transistors, the latter with ring emitter structure and paired Beta Ic/Ib
  • Low-induction emitter resistors from Noble company
  • Professional FR4 printed circuit board with fabric insert
  • Improved version of the P100 stereo amplifier with optimized layout and RF irradiance
  • There are 2 variants of the P101 in protection class I
    • in the early 90s with manufacturer country information "Made in England" on the back
    • Middle of the 90s without manufacturer country information on the back, where the following modifications have been carried out.
      • Modified inner chassis with mechanically optimized transformer mounting
      • Toroidal core transformer with double output windings connected in parallel. --> less mechanical transformer hum
      • Reduced base current (bias current) of the output stage transistors approx. 65mA/140mV (old 95mA/210mV) --> less heating
      • Pre-driver stage with changed temperature compensation
      • changed RC element for compensation of the oscillation tendency
    • < li>The P101 Made in England can be converted into the new version by assembly modifications.
  • Early 90s with manufacturer country information "Made in England" on the back
  • Middle of the 90s without manufacturer country information on the back, where the following modifications were carried out.
    • Modified inner chassis with mechanically optimized transformer mounting
    • Toroidal core transformer with double output windings connected in parallel. --> less mechanical transformer hum
    • Reduced base current (bias current) of the output stage transistors approx. 65mA/140mV (old 95mA/210mV) --> less heating
    • Pre-driver stage with changed temperature compensation
    • changed RC element for compensation of the oscillation tendency
  • < li>The P101 Made in England can be converted into the new version by assembly modifications.
  • Modified inner chassis with mechanically optimized transformer mounting
  • Toroidal core transformer with double output windings connected in parallel. --> less mechanical transformer hum
  • Reduced base current (bias current) of the output stage transistors approx. 65mA/140mV (old 95mA/210mV) --> less heating
  • Pre-driver stage with changed temperature compensation
  • changed RC element for compensation of the oscillation tendency
    < li>Later also available as CE version with protection class II insulation, i.e. without 3rd ground connection in the cold appliance connection

Camtech P101


Comment:



Comment box:


Camtech P101 relate